Products
Distributors
Manufacturers
- Intel
- Samsung
- Texas Instruments
- STMicroelectronics
- Infineon
- NXP Semiconductors
- Microchip
- Analog Devices
- onsemi
- Skyworks Solutions
- Avago
- Marvell
- Omnivision Technologies
- ROHM
- Seoul Semiconductor
- Silego
- Cirrus Logic
- Silicon Labs
- Lattice Semiconductor
- Cypress Semiconductor
- Toshiba
- Mitsubishi
- Panasonic
- Sharp
- Omnetics
- Laird
- TDK-Lambda
- WAGO
- All Distributors
Adafruit Industries
Visit SiteADA476
Manufacturers :Adafruit Industries
A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. They're the same size as common arcade controls (often referred to as 30mm diameter) but have some nice things going for them that justify the extra dollar. First, they look fantastic, all 6 colors have a crystal translucent glossy look. Although they do not have LEDs built in, we're confident that sticking a diffused LED into the body would make it light up very nicely. They are also shorter than cheap arcade controls, and snap into place, so you only need 1.5 of depth (1.25 if you bend the contacts over). The button action is smooth, without a strong click, yet you can definitely feel when the button is pressed. A tiny micro-switch is pre-installed, with gold plated contacts.
ADA482
Manufacturers :Adafruit Industries
Weatherproof Metal On/Off Switch with Green LED Ring
ADA492
Manufacturers :Adafruit Industries
A button is a button, and a switch is a switch, but this LED illuminated arcade buttons is in a class of its own. Its the same size as a 'standard' 30mm arcade but has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic, and a lamp holder fits inside. These were originally designed for 'incandescent' lamps but is easy to use with an LED, just wrap the legs around the holder as shown. It comes with a clear white LED but honestly, we suggest finding a diffused LED to use instead, with a wide illumination since this clear one doesn't fill the circle as nicely as it could. (The button factory didn't have diffused LEDs available). You can even disassemble the button itself and slip an image under the clear cover for backlighting. The button comes with a normally-open micro-switch. Once you have put in the LED you like, just snap in the micro-switch. You can always remove it later to change out the LED color. The micro-switch is fairly clicky, so you will hear and feel it when it actuates.
ADA1404
Manufacturers :Adafruit Industries
It looks like a servo, it acts like a servo, but it's more than just a servo! We got a factory to custom-make these classic 'standard' sized hobby servos with a twist - the feedback (potentiometer wiper) line is brought out to a fourth white wire. You can read this wire with an analog input such as those on an Arduino, to get the servo's position. That information can be used in robotics to improve stability or even allow 'recording' of servo motion. Check out our example Arduino sketch which demonstrates how to record motion data to the EEPROM and then play it back when a button is pressed. Comes with a range of horns as seen above. Analog Feedback Servo (255)
ADA1186
Manufacturers :Adafruit Industries
OMG WATCH OUT! This 100mm diameter arcade button is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying beep!. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a domed yellow plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED has a built in resistor so you can run it up to 12V but given the massive size and shallow depth of the button, it doesn't illuminate the entire button face evenly. The button activates a common arcade microswitch (included), the switch contacts are normally open. When the button is pressed, the contacts close. Massive Arcade Button with LED - 100mm Yellow (059)
ADA1185
Manufacturers :Adafruit Industries
OMG WATCH OUT! This 100mm diameter arcade button is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying beep!. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a domed red plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED has a built in resistor so you can run it up to 12V but given the massive size and shallow depth of the button, it doesn't illuminate the entire button face evenly. The button activates a common arcade microswitch (included), the switch contacts are normally open. When the button is pressed, the contacts close. Massive Arcade Button with LED - 100mm Red (059)
ADA1189
Manufacturers :Adafruit Industries
OMG WATCH OUT! This 100mm diameter arcade button is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying beep!. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a domed blue plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED has a built in resistor so you can run it up to 12V but given the massive size and shallow depth of the button, it doesn't illuminate the entire button face evenly. The button activates a common arcade microswitch (included), the switch contacts are normally open. When the button is pressed, the contacts close. Massive Arcade Button with LED - 100mm Blue (059)
ADA1187
Manufacturers :Adafruit Industries
OMG WATCH OUT! This 100mm diameter arcade button is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying beep!. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a domed white plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED has a built in resistor so you can run it up to 12V but given the massive size and shallow depth of the button, it doesn't illuminate the entire button face evenly. The button activates a common arcade microswitch (included), the switch contacts are normally open. When the button is pressed, the contacts close. Massive Arcade Button with LED - 100mm White (059)
ADA1611
Manufacturers :Adafruit Industries
So squishy! These silicone elastomer keypads are just waiting for your fingers to press them. Go ahead, squish all you like! (They're durable and easy to clean, just wipe with mild soap and water) These are just like the light up rubber buttons you find on stuff like appliances and tools, but these are open source and easy to integrate into your next project. Each button is 10mm x 10mm square and 10mm tall. There is 5mm of grid spacing between the buttons. You can 'tile' the button pads edge-to-edge and they'll grid up correctly. You can also cut the pads down if you like, the silicone is very soft. The way they're molded, they give about 3mm of travel when pressed for a very satisfying feel. They are completely quiet, however. On the bottom of each button is a conductive pad ring which can close a properly design contact underneath. We have an EagleCad library which has objects for the buttons and optional LEDs so you can use them in your next PCB design. Each button is 10mm tall and can fit a 3mm LED inside quite easily. 5mm LEDs are too big, so stick with 3mm here. The LED is optional, having it or not does not affect the 'action'. but it's nice to backlight buttons. Diffused LEDs are best, so check out our offerings the blue, white and red look best, if you're sourcing your own LEDs go for something with 300mcd or greater brightness. Diffused looks better than not. Chances are you don't want to make your own PCB, so pick up an Adafruit Trellis, our tile-able driver which can control 16 LEDs + these 16 buttons over I2C Check out our github repository for 3D CAD files and an Eagle library with ready-to-go objects
ADA1489
Manufacturers :Adafruit Industries
Slim clicky momentary switches are standard input buttons on electronic projects. These are half the width of classic 6mm tactile switches so they line up better on a breadboard, just plug them into every-other row. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The two pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They come in a pack of 20, they're pretty handy so you'll want to keep them around. Tactile Switch Buttons (6mm slim) x 20 pack (210)
- 1
- 2
- 3